Buzz in the opposite direction of hair growth. Hair growth direction is different for everyone and it also may vary on different parts of your head.
Run your fingers through your hair to figure out the direction of growth — the places where you feel the most force against your fingers indicates growth in that direction. When you use anything less than a 3 clipper guard, your scalp will be visible. Do the sides first. Start at the back of the neck and move the direction of the clippers up to ear level.
Trim around the ears with a special clipper, which you were hopefully able to obtain. Then buzz from ear to temple level. If you have persistent long pieces, cut them carefully with scissors. Use your hand as a guide for cutting the back. Your hand will act as a guide so that you can avoid cutting too far up or crookedly. Starting at the bottom, drag the clippers up through your hair until you bump against your hand. Put the clippers down and use the second mirror to check your work.
Drag the clippers from forehead to crown to buzz the top. Do a couple of passes with the clippers, then check to see if anything needs fixing. Due to the curve of the head, it's easy to miss some longer pieces. Try different directions to get any stray pieces that might be lingering. Try going side to side across the top of the head, and both forward and backwards.
Feel for any leftover long pieces with your fingers and clean up whatever remains. Clean up the hairline. Do the back of the neck without a guard on the clippers. Use your hand, a headband, a piece of tape, or something else as a guide for the back of the neck. Apply pressure with the clippers and move them move slowly until you hit the edge of the guide.
Use two mirrors or a camera to check your work and clean it up if needed. Be careful not to cut an uneven line at the bottom of the style. Part 3. Maintain your blades. Always remove any hair after using the blade. Keep the guards tidy and in order. Store all of the pieces in a case together with the clippers. Rub a few drops of oil into the blade every few times you use it.
Check your manual for any specific care your particular blades may need. After having your clippers for a while, you may begin to notice that it is cutting unevenly and pulling at your hair. This means you either need to sharpen or replace your blades, whichever you prefer. Invest in hair gel or wax for styling. To style shorter length buzzcuts, apply a pea-sized amount of gel or wax on the top of your head.
Run your fingers up through the hair to distribute the product. This will give it texture and spike it up. Develop and improve products. List of Partners vendors. Buzzcuts are quite possibly the easiest hairstyle to maintain next to an all-out shave, making it an ideal year-round look. The style has deep, powerful roots in history and pop culture, such as it being a recruitment haircut for members of the military which was initiially a practical move to ward off lice within the camp and a nod to androgyny from Hollywood celebs like Grace Jones, Adwoa Aboah, and Kristen Stewart.
Whether your reasoning for a buzzcut is a power move or a quest for simplicity, all you need is 15 minutes to do your own buzzcut from the comfort of your home. Below, we've created a step-by-step guide to a DIY-ing the look.
A buzzcut is a short haircut style in which clippers are used to achieve a tapered look. Before giving yourself a buzzcut, you may want to watch a hairstylist or barber do it either on YouTube or in person. Pay close attention to what they're doing. Watch how they move the clipper up the head. Also, expectedly, know that buzzing your head will leave clippings all over your floor.
Put something on the floor to catch the hair, like plastic or newspaper, and cover yourself with a towel so you protect your clothes or just take your shirt off. Invest in good tools, and keep your clippers well-oiled and maintained. Together, these will set you back around a hundred bucks, but they'll give you years of use, and you'll recover the cost from saving cash spent getting your hair professionally done. If you decide to buzz it all the way to the skin, a good balding clipper is a great investment.
When you're cutting, don't rush it. Be careful and proceed slowly to keep from making a mistake. Make sure your guards are on securely. If the clipper guard pops off, you'll end up with a bald patch that can only be fixed by shaving your head, so make sure your guards are firmly attached to the clipper before you proceed. The standard cut you should go with is a buzzcut, which has a No. The shorter you buzz it, the harder it will be to mess up or end up with an uneven result.
To achieve the best results, it's helpful to start with a clean, dry head of hair —hair will be more difficult to cut evenly if it has product in it or is flat after sleeping or wearing a hat.
Buzz cuts require minimal equipment: all you need is a pair of clippers with multiple guards. Stylist Vernon Scott , who works with Danai Gurira, Cynthia Erivo, and Idris Elba, recommends the brand Andis as "they have a full line of professional and personal products perfect for everyone from the novice to the expert.
Beard trimmers and hair clippers are quite different. If you are new to the world of buzz cuts, the science is simple. O'Rourke recommends picking a guard that doesn't go brutally short on the first go. That way, you're in control. Make sure they are on securely before you start cutting.
You may opt-out by clicking here. More From Vetted. Dec 3, , pm EST. Nov 12, , pm EST. Nov 12, , am EST. Nov 11, , pm EST. All products and services featured are independently selected by Forbes Shopping contributors and editors.
When you make a purchase through links on this page, we may earn a commission. Edit Story. May 15, , am EDT. Adam Hurly Contributor.
0コメント